Home > Articles > Cisco > CCNP Routing and Switching

This chapter is from the book

Foundation Topics

IEEE 802.1D Overview

A robust network design not only includes efficient transfer of packets or frames, but also considers how to recover quickly from faults in the network. In a Layer 3 environment, the routing protocols in use keep track of redundant paths to a destination network so that a secondary path can be used quickly if the primary path fails. Layer 3 routing allows many paths to a destination to remain up and active, and allows load sharing across multiple paths.

In a Layer 2 environment (switching or bridging), however, no routing protocols are used, and active redundant paths are neither allowed nor desirable. Instead, some form of bridging provides data transport between networks or switch ports. The Spanning Tree Protocol (STP) provides network link redundancy so that a Layer 2 switched network can recover from failures without intervention in a timely manner. The STP is defined in the IEEE 802.1D standard.

STP is discussed in relation to the problems it solves in the sections that follow.

Bridging Loops

Recall that a Layer 2 switch mimics the function of a transparent bridge. A transparent bridge must offer segmentation between two networks while remaining transparent to all the end devices connected to it. For the purpose of this discussion, consider a two-port Ethernet switch and its similarities to a two-port transparent bridge.

A transparent bridge (and the Ethernet switch) must operate as follows:

  • The bridge has no initial knowledge of any end device's location; therefore, the bridge must "listen" to frames coming into each of its ports to figure out on which network each device resides. The bridge assumes that a device using the source MAC address is located behind the port that the frame arrives on. As the listening process continues, the bridge builds a table that correlates source MAC addresses with the Bridge Port numbers where they were detected.

    The bridge constantly can update its bridging table upon detecting the presence of a new MAC address or upon detecting a MAC address that has changed location from one Bridge Port to another. The bridge then can forward frames by looking at the destination MAC address, looking up that address in the bridge table, and sending the frame out the port where the destination device is known to be located.

  • If a frame arrives with the broadcast address as the destination address, the bridge must forward, or flood, the frame out all available ports. However, the frame is not forwarded out the port that initially received the frame. In this way, broadcasts can reach all available Layer 2 networks. A bridge segments only collision domains—it does not segment broadcast domains.
  • If a frame arrives with a destination address that is not found in the bridge table, the bridge cannot determine which port to forward the frame to for transmission. This type of frame is known as an unknown unicast. In this case, the bridge treats the frame as if it were a broadcast and floods it out all remaining ports. When a reply to that frame is overheard, the bridge can learn the location of the unknown station and can add it to the bridge table for future use.
  • Frames forwarded across the bridge cannot be modified by the bridge itself. Therefore, the bridging process is effectively transparent.

Bridging or switching in this fashion works well. Any frame forwarded, whether to a known or unknown destination, is forwarded out the appropriate port or ports so that it is likely to be received successfully at the end device. Figure 9-1 shows a simple two-port switch functioning as a bridge, forwarding frames between two end devices. However, this network design offers no additional links or paths for redundancy if the switch or one of its links fails. In that case, the networks on either side of the bridge would become isolated from each other.

09fig01.gif

Figure 9-1 Transparent Bridging with a Switch

To add some redundancy, you can add a second switch between the two original network segments, as shown in Figure 9-2. Now, two switches offer the transparent bridging function in parallel. In theory, a single switch or a single link can fail without causing end-to-end connectivity to fail.

09fig02.gif

Figure 9-2 Redundant Bridging with Two Switches

Consider what happens when PC-1 sends a frame to PC-4. For now, assume that both PC-1 and PC-4 are known to the switches and are in their address tables. PC-1 sends the frame onto network Segment A. Switch A and switch B both receive the frame on their 1/1 ports. Because PC-4 already is known to the switches, the frame is forwarded out ports 2/1 on each switch onto Segment B. The end result is that PC-4 receives two copies of the frame from PC-1. This is not ideal, but it is not disastrous, either.

Now, consider the same process of sending a frame from PC-1 to PC-4. This time, however, neither switch knows anything about the location of PC-1 or PC-4. PC-1 sends the frame to PC-4 by placing it on Segment A. The sequence of events is as follows:

  1. Both Switch A and switch B receive the frame on their 1/1 ports. Because the MAC address of PC-1 has not yet been seen or recorded, each switch records PC-1's MAC address in its address table along with the receiving port number, 1/1. From this information, both switches infer that PC-1 must reside on Segment A.
  2. Because the location of PC-4 is unknown, both switches correctly decide that they must flood the frame out all available ports. This is an unknown unicast condition and is their best effort to make sure that the frame eventually reaches its destination.
  3. Each switch floods or copies the frame to its 2/1 port on Segment B. PC-4, located on Segment B, receives the two frames destined for it. However, on Segment B, switch A now hears the new frame forwarded by switch B, and switch B hears the new frame forwarded by switch A.
  4. Switch A sees that the "new" frame is from PC-1 to PC-4. From the address table, the switch previously learned that PC-1 was on port 1/1, or Segment A. However, the source address of PC-1 has just been heard on port 2/1, or Segment B. By definition, the switch must relearn the location of PC-1 with the most recent information, which it now incorrectly assumes to be Segment B. (Switch B follows the same procedure, based on the "new" frame from switch A.)
  5. At this point, neither switch A nor switch B has learned the location of PC-4 because no frames have been received with PC-4 as the source address. Therefore, the new frame must be flooded out all available ports in an attempt to find PC-4. This frame then is sent out switch A's 1/1 port and onto Segment A, as well as switch B's 1/1 port and onto Segment A.
  6. Now both switches relearn the location of PC-1 as Segment A and forward the "new" frames back onto Segment B; then the entire process repeats.

This process of forwarding a single frame around and around between two switches is known as a bridging loop. Neither switch is aware of the other, so each happily forwards the same frame back and forth between its segments. Also note that because two switches are involved in the loop, the original frame has been duplicated and now is sent around in two counter-rotating loops. What stops the frame from being forwarded in this fashion forever? Nothing! PC-4 begins receiving frames addressed to it as fast as the switches can forward them.

Notice how the learned location of PC-1 keeps changing as frames get looped. Even a simple unicast frame has caused a bridging loop to form, and each switch's bridge table repeatedly is corrupted with incorrect data.

What would happen if PC-1 sent a broadcast frame instead? The bridging loops (remember that two of them are produced by the two parallel switches) form exactly as before. The broadcast frames continue to circulate forever. Now, however, every end-user device located on both Segments A and B receives and processes every broadcast frame. This type of broadcast storm easily can saturate the network segments and bring every host on the segments to a halt.

The only way to end the bridging loop condition is to physically break the loop by disconnecting switch ports or shutting down a switch. Obviously, it would be better to prevent bridging loops than to be faced with finding and breaking them after they form.

Preventing Loops with Spanning Tree Protocol

Bridging loops form because parallel switches (or bridges) are unaware of each other. STP was developed to overcome the possibility of bridging loops so that redundant switches and switch paths could be used for their benefits. Basically, the protocol enables switches to become aware of each other so they can negotiate a loop-free path through the network.

Loops are discovered before they are made available for use, and redundant links effectively are shut down to prevent the loops from forming. In the case of redundant links, switches can be made aware that a link shut down for loop prevention should be brought up quickly in case of a link failure. The section "Redundant Link Convergence," in Chapter 10.

STP is communicated among all connected switches on a network. Each switch executes the Spanning Tree Algorithm based on information received from other neighboring switches. The algorithm chooses a reference point in the network and calculates all the redundant paths to that reference point. When redundant paths are found, the Spanning Tree Algorithm picks one path by which to forward frames and disables, or blocks, forwarding on the other redundant paths.

As its name implies, STP computes a tree structure that spans all switches in a subnet or network. Redundant paths are placed in a Blocking or Standby state to prevent frame forwarding. The switched network is then in a loop-free condition. However, if a forwarding port fails or becomes disconnected, the Spanning Tree Algorithm recomputes the spanning-tree topology so that the appropriate blocked links can be reactivated.

Spanning-Tree Communication: Bridge Protocol Data Units

STP operates as switches communicate with one another. Data messages are exchanged in the form of Bridge Protocol Data Units (BPDU). A switch sends a BPDU frame out a port, using the unique MAC address of the port itself as a source address. The switch is unaware of the other switches around it, so BPDU frames are sent with a destination address of the well-known STP multicast address 01-80-c2-00-00-00.

Two types of BPDU exist:

  • Configuration BPDU, used for spanning-tree computation
  • Topology Change Notification (TCN) BPDU, used to announce changes in the network topology

The Configuration BPDU message contains the fields shown in Table 9-2. The TCN BPDU is discussed in the "Topology Changes" section later in this chapter.

Table 9-2. Configuration BPDU Message Content

Field Description

Number of Bytes

Protocol ID (always 0)

2

Version (always 0)

1

Message Type (Configuration or TCN BPDU)

1

Flags

1

Root Bridge ID

8

Root Path Cost

4

Sender Bridge ID

8

Port ID

2

Message Age (in 256ths of a second)

2

Maximum Age (in 256ths of a second)

2

Hello Time (in 256ths of a second)

2

Forward Delay (in 256ths of a second)

2

The exchange of BPDU messages works toward the goal of electing reference points as a foundation for a stable spanning-tree topology. Loops also can be identified and removed by placing specific redundant ports in a Blocking or Standby state. Notice that several key fields in the BPDU are related to bridge (or switch) identification, path costs, and timer values. These all work together so that the network of switches can converge upon a common spanning-tree topology and select the same reference points within the network. These reference points are defined in the sections that follow.

By default, BPDUs are sent out all switch ports every 2 seconds so that current topology information is exchanged and loops are identified quickly.

Electing a Root Bridge

For all switches in a network to agree on a loop-free topology, a common frame of reference must exist to use as a guide. This reference point is called the Root Bridge. (The term bridge continues to be used even in a switched environment because STP was developed for use in bridges. Therefore, when you see bridge, think switch.)

An election process among all connected switches chooses the Root Bridge. Each switch has a unique Bridge ID that identifies it to other switches. The Bridge ID is an 8-byte value consisting of the following fields:

  • Bridge Priority (2 bytes)— The priority or weight of a switch in relation to all other switches. The priority field can have a value of 0 to 65,535 and defaults to 32,768 (or 0x8000) on every Catalyst switch.
  • MAC Address (6 bytes)— The MAC address used by a switch can come from the Supervisor module, the backplane, or a pool of 1024 addresses that are assigned to every Supervisor or backplane, depending on the switch model. In any event, this address is hardcoded and unique, and the user cannot change it.

When a switch first powers up, it has a narrow view of its surroundings and assumes that it is the Root Bridge itself. (This notion probably will change as other switches check in and enter the election process.) The election process then proceeds as follows: Every switch begins by sending out BPDUs with a Root Bridge ID equal to its own Bridge ID and a Sender Bridge ID that is its own Bridge ID. The Sender Bridge ID simply tells other switches who is the actual sender of the BPDU message. (After a Root Bridge is decided upon, configuration BPDUs are sent only by the Root Bridge. All other bridges must forward or relay the BPDUs, adding their own Sender Bridge IDs to the message.)

Received BPDU messages are analyzed to see if a "better" Root Bridge is being announced. A Root Bridge is considered better if the Root Bridge ID value is lower than another. Again, think of the Root Bridge ID as being broken into Bridge Priority and MAC address fields. If two Bridge Priority values are equal, the lower MAC address makes the Bridge ID better. When a switch hears of a better Root Bridge, it replaces its own Root Bridge ID with the Root Bridge ID announced in the BPDU. The switch then is required to recommend or advertise the new Root Bridge ID in its own BPDU messages, although it still identifies itself as the Sender Bridge ID.

Sooner or later, the election converges and all switches agree on the notion that one of them is the Root Bridge. As might be expected, if a new switch with a lower Bridge Priority powers up, it begins advertising itself as the Root Bridge. Because the new switch does indeed have a lower Bridge ID, all the switches soon reconsider and record it as the new Root Bridge. This also can happen if the new switch has a Bridge Priority equal to that of the existing Root Bridge but has a lower MAC address. Root Bridge election is an ongoing process, triggered by Root Bridge ID changes in the BPDUs every 2 seconds.

As an example, consider the small network shown in Figure 9-3. For simplicity, assume that each Catalyst switch has a MAC address of all 0s, with the last hex digit equal to the switch label.

09fig03.gif

Figure 9-3 Example of Root Bridge Election

In this network, each switch has the default Bridge Priority of 32,768. The switches are inter-connected with Fast Ethernet links. All three switches try to elect themselves as the Root, but all of them have equal Bridge Priority values. The election outcome produces the Root Bridge, determined by the lowest MAC address—that of Catalyst A.

Electing Root Ports

Now that a reference point has been nominated and elected for the entire switched network, each nonroot switch must figure out where it is in relation to the Root Bridge. This action can be performed by selecting only one Root Port on each nonroot switch. The Root Port always points toward the current Root Bridge.

STP uses the concept of cost to determine many things. Selecting a Root Port involves evaluating the Root Path Cost. This value is the cumulative cost of all the links leading to the Root Bridge. A particular switch link also has a cost associated with it, called the Path Cost. To understand the difference between these values, remember that only the Root Path Cost is carried inside the BPDU. (See Table 9-2 again.) As the Root Path Cost travels along, other switches can modify its value to make it cumulative. The Path Cost, however, is not contained in the BPDU. It is known only to the local switch where the port (or "path" to a neighboring switch) resides.

Path Costs are defined as a 1-byte value, with the default values shown in Table 9-3. Generally, the higher the bandwidth of a link, the lower the cost of transporting data across it. The original IEEE 802.1D standard defined Path Cost as 1000 Mbps divided by the link bandwidth in megabits per second. These values are shown in the center column of the table. Modern networks commonly use Gigabit Ethernet and OC-48 ATM, which are both either too close to or greater than the maximum scale of 1000 Mbps. The IEEE now uses a nonlinear scale for Path Cost, as shown in the right column of the table.

Table 9-3. STP Path Cost

Link Bandwidth

Old STP Cost

New STP Cost

4 Mbps

250

250

10 Mbps

100

100

16 Mbps

63

62

45 Mbps

22

39

100 Mbps

10

19

155 Mbps

6

14

622 Mbps

2

6

1 Gbps

1

4

10 Gbps

0

2

The Root Path Cost value is determined in the following manner:

  1. The Root Bridge sends out a BPDU with a Root Path Cost value of 0 because its ports sit directly on the Root Bridge.
  2. When the next-closest neighbor receives the BPDU, it adds the Path Cost of its own port where the BPDU arrived. (This is done as the BPDU is received.)
  3. The neighbor sends out BPDUs with this new cumulative value as the Root Path Cost.
  4. The Root Path Cost is incremented by the ingress port Path Cost as the BPDU is received at each switch down the line.
  5. Notice the emphasis on incrementing the Root Path Cost as BPDUs are received. When computing the Spanning Tree Algorithm manually, remember to compute a new Root Path Cost as BPDUs come in to a switch port, not as they go out.

After incrementing the Root Path Cost, a switch also records the value in its memory. When a BPDU is received on another port and the new Root Path Cost is lower than the previously recorded value, this lower value becomes the new Root Path Cost. In addition, the lower cost tells the switch that the path to the Root Bridge must be better using this port than it was on other ports. The switch now has determined which of its ports has the best path to the Root: the Root Port.

Figure 9-4 shows the same network from Figure 9-3 in the process of Root Port selection.

09fig04.gif

Figure 9-4 Example of Root Port Selection

The Root Bridge, Catalyst A, already has been elected. Therefore, every other switch in the network must choose one port that has the best path to the Root Bridge. Catalyst B selects its port 1/1, with a Root Path Cost of 0 plus 19. Port 1/2 is not chosen because its Root Path Cost is 0 (BPDU from Catalyst A) plus 19 (Path Cost of A–C link), plus 19 (Path Cost of C–B link), or a total of 38. Catalyst C makes a similar choice of port 1/1.

Electing Designated Ports

By now, you should begin to see the process unfolding: A starting or reference point has been identified, and each switch "connects" itself toward the reference point with the single link that has the best path. A tree structure is beginning to emerge, but links have only been identified at this point. All links still are connected and could be active, leaving bridging loops.

To remove the possibility of bridging loops, STP makes a final computation to identify one Designated Port on each network segment. Suppose that two or more switches have ports connected to a single common network segment. If a frame appears on that segment, all the bridges attempt to forward it to its destination. Recall that this behavior was the basis of a bridging loop and should be avoided.

Instead, only one of the links on a segment should forward traffic to and from that segment—the one that is selected as the Designated Port. Switches choose a Designated Port based on the lowest cumulative Root Path Cost to the Root Bridge. For example, a switch always has an idea of its own Root Path Cost, which it announces in its own BPDUs. If a neighboring switch on a shared LAN segment sends a BPDU announcing a lower Root Path Cost, the neighbor must have the Designated Port. If a switch learns only of higher Root Path Costs from other BPDUs received on a port, however, it then correctly assumes that its own receiving port is the Designated Port for the segment.

Notice that the entire STP determination process has served only to identify bridges and ports. All ports are still active, and bridging loops still might lurk in the network. STP has a set of progressive states that each port must go through, regardless of the type or identification. These states actively prevent loops from forming and are described in the next section.

Figure 9-5 demonstrates an example of Designated Port selection. This figure is identical to Figure 9-3 and Figure 9-4, with further spanning-tree development shown. The only changes are the choices of Designated Ports, although seeing all STP decisions shown on one network diagram is handy.

09fig05.gif

Figure 9-5 Example of Designated Port Selection

The three switches have chosen their Designated Ports (DP) for the following reasons:

  • Catalyst A— Because this switch is the Root Bridge, all its active ports are Designated Ports, by definition. At the Root Bridge, the Root Path Cost of each port is 0.
  • Catalyst B— Catalyst A port 1/1 is the DP for the Segment A–B because it has the lowest Root Path Cost (0). Catalyst B port 1/2 is the DP for segment B–C. The Root Path Cost for each end of this segment is 19, determined from the incoming BPDU on port 1/1. Because the Root Path Cost is equal on both ports of the segment, the DP must be chosen by the next criteria—the lowest Sender Bridge ID. When Catalyst B sends a BPDU to Catalyst C, it has the lowest MAC address in the Bridge ID. Catalyst C also sends a BPDU to Catalyst B, but its Sender Bridge ID is higher. Therefore, Catalyst B port 1/2 is selected as the segment's DP.
  • Catalyst C— Catalyst A port 1/2 is the DP for Segment A–C because it has the lowest Root Path Cost (0). Catalyst B port 1/2 is the DP for Segment B–C. Therefore, Catalyst C port 1/2 will be neither a Root Port nor a Designated Port. As discussed in the next section, any port that is not elected to either position enters the Blocking state. Where blocking occurs, bridging loops are broken.

STP States

To participate in STP, each port of a switch must progress through several states. A port begins its life in a Disabled state, moving through several passive states and, finally, into an active state if allowed to forward traffic. The STP port states are as follows:

  • Disabled— Ports that are administratively shut down by the network administrator, or by the system because of a fault condition, are in the Disabled state. This state is special and is not part of the normal STP progression for a port.
  • Blocking— After a port initializes, it begins in the Blocking state so that no bridging loops can form. In the Blocking state, a port cannot receive or transmit data and cannot add MAC addresses to its address table. Instead, a port is allowed to receive only BPDUs so that the switch can hear from other neighboring switches. In addition, ports that are put into standby mode to remove a bridging loop enter the Blocking state.
  • Listening— A port is moved from Blocking to Listening if the switch thinks that the port can be selected as a Root Port or Designated Port. In other words, the port is on its way to begin forwarding traffic.In the Listening state, the port still cannot send or receive data frames. However, the port is allowed to receive and send BPDUs so that it actively can participate in the Spanning Tree topology process. Here, the port finally is allowed to become a Root Port or Designated Port because the switch can advertise the port by sending BPDUs to other switches. If the port loses its Root Port or Designated Port status, it returns to the Blocking state.
  • Learning— After a period of time called the Forward Delay in the Listening state, the port is allowed to move into the Learning state. The port still sends and receives BPDUs as before. In addition, the switch now can learn new MAC addresses to add to its address table. This gives the port an extra period of silent participation and allows the switch to assemble at least some address table information. The port cannot yet send any data frames, however.
  • Forwarding— After another Forward Delay period of time in the Learning state, the port is allowed to move into the Forwarding state. The port now can send and receive data frames, collect MAC addresses in its address table, and send and receive BPDUs. The port is now a fully functioning switch port within the spanning-tree topology.Remember that a switch port is allowed into the Forwarding state only if no redundant links (or loops) are detected and if the port has the best path to the Root Bridge as the Root Port or Designated Port.

Example 9-1 shows the output from a switch as one of its ports progresses through the STP port states.

Example 9-1. Port Progressing Through the STP Port States

*Mar 16 14:31:00 UTC: STP SW: Fa0/1 new disabled req for 1 vlans
Switch(config)# interface fast 0/1
Switch(config-if)#no shut
Switch(config-if)#^-Z
*Mar 16 14:31:00 UTC: STP SW: Fa0/1 new blocking req for 1 vlans

Switch#show spanning interface fast 0/1

Vlan             Port ID                     Designated                Port ID
Name             Prio.Nbr      Cost Sts      Cost Bridge ID            Prio.Nbr
---------------- -------- --------- --- --------- -------------------- --------
VLAN0001         128.1           19 LIS         0 32769 000a.f40a.2980 128.1

*Mar 16 14:31:15 UTC: STP SW: Fa0/1 new learning req for 1 vlans

Switch#show spanning interface fast 0/1
Vlan             Port ID                     Designated                Port ID
Name             Prio.Nbr      Cost Sts      Cost Bridge ID            Prio.Nbr
---------------- -------- --------- --- --------- -------------------- --------
VLAN0001         128.1           19 LRN         0 32768 00d0.5849.4100  32.129

*Mar 16 14:31:30 UTC: STP SW: Fa0/1 new forwarding req for 1 vlans

Switch#show spanning interface fast 0/1

Vlan             Port ID                     Designated                Port ID
Name             Prio.Nbr      Cost Sts      Cost Bridge ID            Prio.Nbr
---------------- -------- --------- --- --------- -------------------- --------
VLAN0001         128.1           19 FWD         0 32768 00d0.5849.4100  32.129

The example begins as the port administratively is disabled from the command line. When the port is enabled, successive show spanning-tree interface type mod/port commands display the port state as Listening, Learning, and then Forwarding. These are shown in the shaded text of the example. Notice also the time stamps and port states provided by the debug spanning-tree switch state command, which give a sense of the timing between port states. Because this port was eligible as a Root Port, the show command never could execute fast enough to show the port in the Blocking state.

STP Timers

STP operates as switches send BPDUs to each other in an effort to form a loop-free topology. The BPDUs take a finite amount of time to travel from switch to switch. In addition, news of a topology change (such as a link or Root Bridge failure) can suffer from propagation delays as the announcement travels from one side of a network to the other. Because of the possibility of these delays, keeping the spanning-tree topology from settling out or converging until all switches have had time to receive accurate information is important.

STP uses three timers to make sure that a network converges properly before a bridging loop can form. The timers and their default values are as follows:

  • Hello Time— The time interval between Configuration BPDUs sent by the Root Bridge. The Hello Time value configured in the Root Bridge switch determines the Hello Time for all nonroot switches because they just relay the Configuration BPDUs as they are received from the root. However, all switches have a locally configured Hello Time that is used to time TCN BPDUs when they are retransmitted. The IEEE 802.1D standard specifies a default Hello Time value of 2 seconds.
  • Forward Delay— The time interval that a switch port spends in both the Listening and Learning states. The default value is 15 seconds.
  • Max (maximum) Age— The time interval that a switch stores a BPDU before discarding it. While executing the STP, each switch port keeps a copy of the "best" BPDU that it has heard. If the switch port loses contact with the BPDU's source (no more BPDUs are received from it), the switch assumes that a topology change must have occurred after the Max Age time elapsed and so the BPDU is aged out. The default Max Age value is 20 seconds.

The STP timers can be configured or adjusted from the switch command line. However, the timer values never should be changed from the defaults without careful consideration. Then the values should be changed only on the Root Bridge switch. Recall that the timer values are advertised in fields within the BPDU. The Root Bridge ensures that the timer values propagate to all other switches.

The network diameter can be configured on the Root Bridge switch to more accurately reflect the true size of the physical network. Making that value more accurate reduces the total STP convergence time during a topology change. Cisco also recommends that if changes need to be made, only the network diameter value should be modified on the Root Bridge switch. When the diameter is changed, the switch calculates new values for all three timers automatically.

Topology Changes

To announce a change in the active network topology, switches send a TCN BPDU. Table 9-4 shows the format of these messages.

Table 9-4. Topology Change Notification BPDU Message Content

Field Description

# of Bytes

Protocol ID (always 0)

2

Version (always 0)

1

Message Type (Configuration or TCN BPDU)

1

A topology change occurs when a switch either moves a port into the Forwarding state or moves a port from the Forwarding or Learning states into the Blocking state. In other words, a port on an active switch comes up or goes down. The switch sends a TCN BPDU out its Root Port so that, ultimately, the Root Bridge receives news of the topology change. Notice that the TCN BPDU carries no data about the change but informs recipients only that a change has occurred. Also notice that the switch will not send TCN BPDUs if the port has been configured with PortFast enabled.

The switch continues sending TCN BPDUs every Hello Time interval until it gets an acknowledgment from its upstream neighbor. As the upstream neighbors receive the TCN BPDU, they propagate it on toward the Root Bridge and send their own acknowledgments. When the Root Bridge receives the TCN BPDU, it also sends out an acknowledgment. However, the Root Bridge sets the Topology Change flag in its Configuration BPDU, which is relayed to every other bridge in the network. This is done to signal the topology change and cause all other bridges to shorten their bridge table aging times from the default (300 seconds) to only the Forward Delay value (default 15 seconds).

This condition causes the learned locations of MAC addresses to be flushed out much sooner than they normally would, easing the bridge table corruption that might occur because of the change in topology. However, any stations that actively are communicating during this time are kept in the bridge table. This condition lasts for the sum of the Forward Delay and the Max Age (default 15 + 20 seconds).

The theory behind topology changes is fairly straightforward, but it's often difficult to grasp how a working network behaves during a change. For example, suppose you have a Layer 2 network (think of a single VLAN or a single instance of STP) that is stable and loop free. If a switch uplink suddenly failed or a new uplink was added, how would the various switches in the network react? Would users all over the network lose connectivity while the STP "recomputes" or reconverges?

Examples of different types of topology changes are presented in the following sections, along with the sequence of STP events. Each type has a different cause and a different effect. To provide continuity as the STP concepts are presented, the same network previously shown in Figures 9-3 through 9-5 is used in each of these examples.

Direct Topology Changes

A direct topology change is one that can be detected on a switch interface. For example, if a trunk link suddenly goes down, the switch on each end of the link immediately can detect a link failure. The absence of that link changes the bridging topology, so other switches should be notified.

Figure 9-6 shows a network that has converged into a stable STP topology. The VLAN is forwarding on all trunk links except port 1/2 on Catalyst C, where it is in the Blocking state.

09fig06.gif

Figure 9-6 Effects of a Direct Topology Change

This network has just suffered a link failure between Catalyst A and Catalyst C. The sequence of events unfolds as follows:

  1. Catalyst C detects a link down on its port 1/1; Catalyst A detects a link down on its port 1/2.
  2. Catalyst C removes the previous "best" BPDU it had received from the Root over port 1/1. Port 1/1 is now down so that BPDU is no longer valid.

    Normally, Catalyst C would try to send a TCN message out its Root Port, to reach the Root Bridge. Here, the Root Port is broken, so that isn't possible. Without an advanced feature such as STP UplinkFast, Catalyst C isn't yet aware that another path exists to the Root.

    Also, Catalyst A is aware of the link down condition on its own port 1/2. It normally would try to send a TCN message out its Root Port, to reach the Root Bridge. Here, Catalyst A is the Root, so that isn't really necessary.

  3. The Root Bridge, Catalyst A, sends a Configuration BPDU with the TCN bit set out its port 1/1. This is received and relayed by each switch along the way, informing each one of the topology change.
  4. Catalysts B and C receive the TCN message. The only reaction these switches take is to shorten their bridging table aging times to the Forward Delay time. At this point, they don't know how the topology has changed; they only know to force fairly recent bridging table entries to age out.
  5. Catalyst C basically just sits and waits to hear from the Root Bridge again. The Config BPDU TCN message is received on port 1/2, which was previously in the Blocking state. This BPDU becomes the "best" one received from the Root, so port 1/2 becomes the new Root Port.

    Catalyst C now can progress port 1/2 from Blocking through the Listening, Learning, and Forwarding states.

As a result of a direct link failure, the topology has changed and STP has converged again. Notice that only Catalyst C has undergone any real effects from the failure. Switches A and B heard the news of the topology change but did not have to move any links through the STP states. In other words, the whole network did not go through a massive STP reconvergence.

The total time that users on Catalyst C lost connectivity was roughly the time that port 1/2 spent in the Listening and Learning states. With the default STP timers, this amounts to about two times the Forward Delay period (15 seconds), or 30 seconds total.

Indirect Topology Changes

Figure 9-7 shows the same network as Figure 9-6, but this time, the link failure indirectly involves Catalysts A and C. The link status at each switch stays up, but something between them has failed or is filtering traffic. This could be another device, such as a service provider's switch, a firewall, and so on. As a result, no data (including BPDUs) can pass between those switches.

09fig07.gif

Figure 9-7 Effects of a Indirect Topology Change

STP can detect and recover from indirect failures, thanks to timer mechanisms. The sequence of events unfolds as follows:

  1. Catalysts A and C both show a link up condition; data begins to be filtered elsewhere on the link.
  2. No link failure is detected, so no TCN messages are sent.
  3. Catalyst C already has stored the "best" BPDU it had received from the Root over port 1/1. No further BPDUs are received from the Root over that port. After the MaxAge timer expires, no other BPDU is available to refresh the "best" entry, so it is flushed. Catalyst C now must wait to hear from the Root again on any of its ports.
  4. The next Configuration BPDU from the Root is heard on Catalyst C port 1/2. This BPDU becomes the new "best" entry, and port 1/2 becomes the Root Port. Now the port is progressed from Blocking through the Listening, Learning, and finally Forwarding states.

As a result of the indirect link failure, the topology doesn't change immediately. The absence of BPDUs from the Root causes Catalyst C to take some action. Because this type of failure relies on STP timer activity, it generally takes longer to detect and mitigate.

In this example, the total time that users on Catalyst C lost connectivity was roughly the time until the MaxAge timer expired (20 seconds), plus the time until the next Configuration BPDU was received (2 seconds) on port 1/2, plus the time that port 1/2 spent in the Listening (15 seconds) and Learning (15 seconds) states. In other words, 52 seconds elapse if the default timer values are used.

Insignificant Topology Changes

Figure 9-8 shows the same network topology as Figure 9-6 and Figure 9-7, with the addition of a user PC on access-layer switch Catalyst C. The user's switch port, 2/12, is just another link as far as the switch is concerned. If the link status goes up or down, the switch must view that as a topology change and inform the Root Bridge.

09fig08.gif

Figure 9-8 Effects of an Insignificant Topology Change

Obviously, user ports are expected to go up and down as the users reboot their machines, turn them on and off as they go to and from work, and so on. Regardless, TCN messages are sent by the switch, just as if a trunk link between switches had changed state.

To see what effect this has on the STP topology and the network, consider the following sequence of events:

  1. The PC on Catalyst port 2/12 is turned off. The switch detects the link status going down.
  2. Catalyst C begins sending TCN BPDUs toward the Root, over its Root Port (1/1).
  3. The Root sends a TCN acknowledgment back to Catalyst C and then sends a Configuration BPDU with the TCN bit set to all downstream switches. This is done to inform every switch of a topology change somewhere in the network.
  4. The TCN flag is received from the Root, and both Catalysts B and C shorten their bridge table aging times. This causes recently idle entries to be flushed, leaving only the actively transmitting stations in the table. The aging time stays short for the duration of the Forward Delay and Max Age timers.

Notice that this type of topology change is mostly cosmetic. No actual topology change occurred because none of the switches had to change port states to reach the Root Bridge. Instead, powering off the PC caused all the switches to age out entries from their bridge or CAM tables much sooner than normal.

At first, this doesn't seem like a major problem because the PC link state affects only the "newness" of the CAM table contents. If CAM table entries are flushed as a result, they probably will be learned again. This becomes a problem when every user PC is considered. Now every time any PC in the network powers up or down, every switch in the network must age out CAM table entries.

Given enough PCs, the switches could be in a constant state of flushing bridge tables. Also remember that when a switch doesn't have a CAM entry for a destination, the packet must be flooded out all its ports. Flushed tables mean more unknown unicasts, which mean more broadcasts or flooded packets throughout the network.

Fortunately, Catalyst switches have a feature that can designate a port as a special case. You can enable the STP PortFast feature on a port with a single attached PC. As a result, TCNs aren't sent when the port changes state, and the port is brought right into the Forwarding state when the link comes up. The section "Redundant Link Convergence," in Chapter 10, covers PortFast in more detail.

Types of STP

So far, this chapter has discussed STP in terms of its operation to prevent loops and to recover from topology changes in a timely manner. STP originally was developed to operate in a bridged environment, basically supporting a single LAN (or one VLAN). Implementing STP into a switched environment has required additional consideration and modification to support multiple VLANs. Because of this, the IEEE and Cisco have approached STP differently. This section reviews the three traditional types of STP that are encountered in switched networks and how they relate to one another. No specific configuration commands are associated with the various types of STP here. Instead, you need a basic understanding of how they interoperate in a network.

Common Spanning Tree

The IEEE 802.1Q standard specifies how VLANs are to be trunked between switches. It also specifies only a single instance of STP that encompasses all VLANs. This instance is referred to as the Common Spanning Tree (CST). All CST BPDUs are transmitted over trunk links using the native VLAN with untagged frames.

Having a single STP for many VLANs simplifies switch configuration and reduces switch CPU load during STP calculations. However, having only one STP instance can cause limitations, too. Redundant links between switches will be blocked with no capability for load balancing. Conditions also can occur that would cause CST to mistakenly enable forwarding on a link that does not carry a specific VLAN, while other links would be blocked.

Per-VLAN Spanning Tree

Cisco has a proprietary version of STP that offers more flexibility than the CST version. Per-VLAN Spanning Tree (PVST) operates a separate instance of STP for each individual VLAN. This allows the STP on each VLAN to be configured independently, offering better performance and tuning for specific conditions. Multiple spanning-trees also make load balancing possible over redundant links when the links are assigned to different VLANs. One link might forward one set of VLANs, while another redundant link might forward a different set.

Because of its proprietary nature, PVST requires the use of Cisco Inter-Switch Link (ISL) trunking encapsulation between switches. In networks where PVST and CST coexist, interoperability problems occur. Each requires a different trunking method, so BPDUs are never exchanged between STP types.

Per-VLAN Spanning Tree Plus

Cisco has a second proprietary version of STP that allows devices to interoperate with both PVST and CST. Per-VLAN Spanning Tree Plus (PVST+) effectively supports three groups of STP operating in the same campus network:

  • Catalyst switches running PVST
  • Catalyst switches running PVST+
  • Switches running CST over 802.1Q

To do this, PVST+ acts as a translator between groups of CST switches and groups of PVST switches. PVST+ can communicate directly with PVST by using ISL trunks. To communicate with CST, however, PVST+ exchanges BPDUs with CST as untagged frames over the native VLAN. BPDUs from other instances of STP (other VLANs) are propagated across the CST portions of the network by tunneling. PVST+ sends these BPDUs by using a unique multicast address so that the CST switches forward them on to downstream neighbors without interpreting them first. Eventually, the tunneled BPDUs reach other PVST+ switches where they are understood.

Pearson IT Certification Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Pearson IT Certification and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Pearson IT Certification products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by Adobe Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.pearsonitcertification.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020