Home > Articles

This chapter is from the book

This chapter is from the book

Connect Devices (1.1.2)

In this section, you will see how accessing a network involves connecting hosts and infrastructure devices with IP addresses, subnet masks, and default gateways. This section will also introduce how to configure the initial settings of a switch.

Connect to a Network (1.1.2.1)

Network devices and end users typically connect to a network using a wired Ethernet or wireless connection. Refer to the sample reference topology in Figure 1-6. The LANs in the figure serve as an example of how users and network devices could connect to networks.

Figure 1-6

Figure 1-6 Sample LAN and WAN Connections

Home Office devices can connect as follows:

  • Laptops and tablets connect wirelessly to a home router.
  • A network printer connects using an Ethernet cable to the switch port on the home router.
  • The home router connects to the service provider cable modem using an Ethernet cable.
  • The cable modem connects to the Internet service provider (ISP) network.

The Branch site devices connect as follows:

  • Corporate resources (i.e., file servers and printers) connect to Layer 2 switches using Ethernet cables.
  • Desktop PCs and voice over IP (VoIP) phones connect to Layer 2 switches using Ethernet cables.
  • Laptops and smartphones connect wirelessly to wireless access points (WAPs).
  • The WAPs connect to switches using Ethernet cables.
  • Layer 2 switches connect to an Ethernet interface on the edge router using Ethernet cables. An edge router is a device that sits at the edge or boundary of a network and routes between that network and another, such as between a LAN and a WAN.
  • The edge router connects to a WAN service provider (SP).
  • The edge router also connects to an ISP for backup purposes.

The Central site devices connect as follows:

  • Desktop PCs and VoIP phones connect to Layer 2 switches using Ethernet cables.
  • Layer 2 switches connect redundantly to multilayer Layer 3 switches using Ethernet fiber-optic cables (orange connections).
  • Layer 3 multilayer switches connect to an Ethernet interface on the edge router using Ethernet cables.
  • The corporate website server is connected using an Ethernet cable to the edge router interface.
  • The edge router connects to a WAN SP.
  • The edge router also connects to an ISP for backup purposes.

In the Branch and Central LANs, hosts are connected either directly or indirectly (via WAPs) to the network infrastructure using a Layer 2 switch.

Default Gateways (1.1.2.2)

To enable network access, devices must be configured with IP address information to identify the appropriate:

  • IP address: Identifies a unique host on a local network
  • Subnet mask: Identifies with which network subnet the host can communicate
  • Default gateway: Identifies the router to send a packet to when the destination is not on the same local network subnet

When a host sends a packet to a device that is on the same IP network, the packet is simply forwarded out of the host interface to the destination device.

When a host sends a packet to a device on a different IP network, then the packet is forwarded to the default gateway, because a host device cannot communicate directly with devices outside of the local network. The default gateway is the destination that routes traffic from the local network to devices on remote networks. It is often used to connect a local network to the Internet.

The default gateway is usually the address of the interface on the router connected to the local network. The router maintains routing table entries of all connected networks as well as entries of remote networks, and determines the best path to reach those destinations.

For example, if PC1 sends a packet to the Web Server located at 172.16.1.99, it would discover that the Web Server is not on the local network and it, therefore, must send the packet to the Media Access Control (MAC) address of its default gateway. The packet protocol data unit (PDU) in Figure 1-7 identifies the source and destination IP and MAC addresses.

Figure 1-7

Figure 1-7 Getting the Pieces to the Correct Network

Document Network Addressing (1.1.2.3)

When designing a new network or mapping an existing network, document the network. At a minimum, the documentation should identify:

  • Device names
  • Interfaces used in the design
  • IP addresses and subnet masks
  • Default gateway addresses

This information is captured by creating two useful network documents:

  • Topology diagram: Provides a visual reference that indicates the physical connectivity and logical Layer 3 addressing. Often created using software, such as Microsoft Visio.
  • Addressing table: A table that captures device names, interfaces, IPv4 addresses, subnet masks, and default gateway addresses.

Figure 1-8 displays the sample topology diagram, while Table 1-2 provides a sample addressing table for the topology.

Figure 1-8

Figure 1-8 Documenting Network Addressing

Table 1-2 Addressing Table

Device

Interface

IP Address

Subnet Mask

Default Gateway

R1

Fa0/0

192.168.1.1

255.255.255.0

N/A

S0/0/0

192.168.2.1

255.255.255.0

N/A

R2

Fa0/0

192.168.3.1

255.255.255.0

N/A

S0/0/0

192.168.2.1

255.255.255.0

N/A

PC1

N/A

192.168.1.10

255.255.255.0

192.168.1.1

PC2

N/A

192.168.1.10

255.255.255.0

192.168.3.1

Enable IP on a Host (1.1.2.4)

A host can be assigned its IP address information in one of two ways. A host can get a:

  • Statically Assigned IP Address: The host is manually assigned the correct IP address, subnet mask, and default gateway. The DNS server IP address can also be configured.
  • Dynamically Assigned IP Address: IP address information is provided by a server using the Dynamic Host Configuration Protocol (DHCP). The DHCP server provides a valid IP address, subnet mask, and default gateway for end devices. Other information may be provided by the server.

Figures 1-9 and 1-10 provide static and dynamic IPv4 address configuration examples.

Figure 1-9

Figure 1-9 Statically Assigning an IP Address

Figure 1-10

Figure 1-10 Dynamically Assigning an IP Address

Statically assigned addresses are commonly used to identify specific network resources, such as network servers and printers. They can also be used in smaller networks with few hosts. However, most host devices acquire their IPv4 address information by accessing a DHCP server. In large enterprises, dedicated DHCP servers providing services to many LANs are implemented. In a smaller branch or small office setting, DHCP services can be provided by a Cisco Catalyst switch or a Cisco ISR.

Device LEDs (1.1.2.5)

Host computers connect to a wired network using a network interface and RJ-45 Ethernet cable. Most network interfaces have one or two LED link indicators next to the interface. Typically, a green LED means a good connection while a blinking green LED indicates network activity.

If the link light is not on, then there may be a problem with either the network cable or the network itself. The switch port where the connection terminates would also have an LED indicator lit. If one or both ends are not lit, try a different network cable.

Similarly, network infrastructure devices commonly use multiple LED indicators to provide a quick status view. For example, a Cisco Catalyst 2960 switch has several status LEDs to help monitor system activity and performance. These LEDs are generally lit green when the switch is functioning normally and lit amber when there is a malfunction.

Cisco ISRs use various LED indicators to provide status information. The LEDs on the router help the network administrator conduct some basic troubleshooting. Each device has a unique set of LEDs. Consult the device-specific documentation for an accurate description of the LEDs.

The LEDs of the Cisco 1941 router shown in Figure 1-11 are explained in Table 1-3.

Figure 1-11

Figure 1-11 Cisco 1941 LEDs

Table 1-3 Description of the Cisco 1941 LEDs

#

Port

LED

Color

Description

1

GE0/0 and GE0/1

S (Speed)

1 blink + pause

Port operating at 10 Mb/s

2 blink + pause

Port operating at 100 Mb/s

3 blink + pause

Port operating at 1000 Mb/s

L (Link)

Green

Link is active

Off

Link is inactive

2

Console

EN

Green

Port is active

Off

Port is inactive

3

USB

EN

Green

Port is active

Off

Port is inactive

Console Access (1.1.2.6)

In a production environment, infrastructure devices are commonly accessed remotely using Secure Shell (SSH) or HyperText Transfer Protocol Secure (HTTPS). Console access is really only required when initially configuring a device, or if remote access fails.

Console access requires:

  • Console cable: RJ-45-to-DB-9 console cable
  • Terminal emulation software: Tera Term, PuTTY, HyperTerminal

The cable is connected between the serial port of the host and the console port on the device. Most computers and notebooks no longer include built-in serial ports. If the host does not have a serial port, the USB port can be used to establish a console connection. A special USB-to-RS-232 compatible serial port adapter is required when using the USB port.

The Cisco ISR G2 supports a USB serial console connection. To establish connectivity, a USB Type-A to USB Type-B (mini-B USB) is required, as well as an operating system device driver. This device driver is available from http://www.cisco.com. Although these routers have two console ports, only one console port can be active at a time. When a cable is plugged into the USB console port, the RJ-45 port becomes inactive. When the USB cable is removed from the USB port, the RJ-45 port becomes active.

Table 1-4 summarizes the console connection requirements, while Figure 1-12 displays the various ports and cables required.

Table 1-4 Console Connection Requirements

Port on Computer

Cable Required

Port on ISR

Terminal Emulation

Serial Port

RJ-45 to DB-9 Console Cable

RJ-45 Console Port

Tera Term PuTTY

USB Type-A Port

USB to RS-232 compatible serial port adapter

  • Adapter may require a software driver

RJ-45 to DB-9 Console Cable

USB Type-A to USB Type-B (Mini-B USB)

  • A device driver is required and available from Cisco.com

USB Type-B(Mini-B USB)

Figure 1-12

Figure 1-12 Ports and Cables

Enable IP on a Switch (1.1.2.7)

Network infrastructure devices require IP addresses to enable remote management. Using the device IP address, the network administrator can remotely connect to the device using Telnet, SSH, HTTP, or HTTPS.

A switch does not have a dedicated interface to which an IP address can be assigned. Instead, the IP address information is configured on a virtual interface called a switched virtual interface (SVI).

The steps to configure the basic settings on a switch are as follows:

how.jpg

Step 1. Name the device.

Step 2. Configure the SVI. This makes the switch accessible for network management.

Step 3. Enable the SVI.

Step 4. Configure the default gateway for the switch. Packets generated by the switch and destined for an address other than its management network segment will be forwarded to this address. This default gateway is used by the switch only for the packets it generates, not any hosts connected to the switch.

For example, the following commands would configure the management VLAN interface and default gateway of switch S1 shown in Figure 1-13.

Figure 1-13

Figure 1-13 Configuring the SVI of S1

S1(config)# interface vlan 1
S1(config-if)# ip address 192.168.10.2 255.255.255.0
S1(config-if)# no shutdown
%LINK-5-CHANGED: Interface Vlan1, changed state to up
S1(config-if)# exit
S1(config)#
S1(config)# ip default-gateway 192.168.10.1
S1(config)#

In the example, the switch SVI is configured and enabled with the IP address 192.168.10.2/24 and a default gateway of the router located at 192.168.10.1. Packets generated by the switch and destined for an address outside of the 192.168.1.0/24 network segment will be forwarded to this address. In the example, the address is that of the G0/0 interface of R1.

Pearson IT Certification Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from Pearson IT Certification and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about Pearson IT Certification products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites; develop new products and services; conduct educational research; and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by Adobe Press. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.pearsonitcertification.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020